GENERAL MOTORS CORP SPECIAL PRODUCTS DEPT -- RTV SILICONE RUBBER T-200B#1052914,1052917  -- 6850-01-167-2003
<pre>=====================  Product Identification  =====================

Product ID:RTV SILICONE RUBBER T-200B#1052914,1052917
MSDS Date:11/22/1985
FSC:6850
NIIN:01-167-2003
=== Responsible Party ===
Company Name:GENERAL MOTORS CORP SPECIAL PRODUCTS DEPT
Address:30007 VAN DYKE
City:WARREN
State:MI
ZIP:48090
Country:US
Info Phone Num:517-263-5711
Emergency Phone Num:517-263-5711
CAGE:11862
=== Contractor Identification ===
Company Name:FASTECH INC
Country:US
CAGE:9N525
Company Name:GENERAL MOTORS CORP CHEVROLET MOTOR DIV
Address:30007 VAN DYKE
Box:City:WARREN
State:MI
ZIP:48090
Country:US
CAGE:11862

=============  Composition/Information on Ingredients  =============

Ingred Name:POLYDIMETHYL SILOXANE FLUID
CAS:9016-00-6
RTECS #:TQ2690000
Fraction by Wt: 62.0%

Ingred Name:INERT FILLER
CAS:989922-04-6
Fraction by Wt: 31.0%

Ingred Name:CARBON BLACK
CAS:1333-86-4
RTECS #:FF5800000
Fraction by Wt: 0.01%
OSHA PEL:3.5 MG/M3
ACGIH TLV:3.5 MG/M3; 9192

Ingred Name:METHYL-TRIS-CYCLOHEXYLAMINO SILANE CURING AGENT
CAS:989933-10-4
Fraction by Wt: 6.0%

Ingred Name:CYCLOHEXYLAMINE  (SARA III)
CAS:108-91-8
RTECS #:GX0700000
Fraction by Wt: 3.0%
OSHA PEL:10 PPM
ACGIH TLV:10 PPM; 9192

=====================  Hazards Identification  =====================

Routes of Entry: Inhalation:YES  Skin:YES  Ingestion:NO
Health Hazards Acute and Chronic:SKIN CONTACT WITH THIS PRODUCT MAY
    CAUSE IRRITATION. EYE CONTACT WITH THIS PRODUCT MAY CAUSE BURNS.
    INHALATION OF VAPORS MAY CAUSE RESPIRATORY IRRITATION.
Effects of Overexposure:CONTACT MAY CAUSE IRRITATION OF THE SKIN AND
    THE RESPIRATORY SYSTEM. EYE CONTACT AY CAUSE BURNS.
Medical Cond Aggravated by Exposure:NO DATA AVAILABLE

=======================  First Aid Measures  =======================

First Aid:EYE: IMMEDIATELY FLUSH EYES WITH LARGE AMOUNTS OF RUNNING
    WATER FOR AT LEAST 15 MINUTES. HOLD EYELIDS APART TO ENSURE RINSING
    OF THE ENTIRE SURFACE OF THE EYE AND LIDS WITH WATER. GET MEDICAL
    ATTENTIO N IMMEDIATELY. SKIN: FLUSH SKIN WELL WITH WATER AND WASH
    WITH SOAP AND WATER. OBTAIN MEDICAL ATTENTION IF IRRITATION OCCURS.
    INGESTION IS UNLIKELY. INHALE: REMOVE TO FRESH AIR.

=====================  Fire Fighting Measures  =====================

Flash Point:NONE
Extinguishing Media:USE WATER FOG, CARBON DIOXIDE, FOAM, OR DRY
    CHEMICAL.
Fire Fighting Procedures:FIRE FIGHTERS SHOULD USE NIOSH APPROVED SCBA &
    FULL PROTECTIVE EQUIPMENT WHEN FIGHTING CHEMICAL FIRE. USE WATER
    SPRAY TO COOL NEARBY CONTAINERS EXPOSED TO FIRE.
Unusual Fire/Explosion Hazard:TOXIC FUMES FORMED ON COMBUSTION.

==================  Accidental Release Measures  ==================

Spill Release Procedures:ABSORB SPILL WITH SAND OR FULLER'S EARTH.
    SWEEP UP AND PLACE IN AN APPROPRIATE CHEMICAL WASTE CONTAINER.
    FLUSH SPILL AREA WITH WATER.

======================	Handling and Storage  ======================

Handling and Storage Precautions:STORE IN A COOL, DRY WELL-VENTILATED
    AREA. EXERCISE CAUTION TO PREVENT DAMAGE TO THE CONTAINER.
Other Precautions:ALL FOOD SHOULD BE KEPT IN A SEPARATE AREA AWAY FORM
    THE STORAGE/USE LOCATION. BEFORE EATING, HANDS AND FACE SHOULD BE
    THOROUGHLY WASHED.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:NOT NEEDED IF THERE IS ADEQUATE VENTILATION.
Ventilation:GENERAL TO MAINTAIN ADEQUATE VENTILATION
Protective Gloves:IMPERVIOUS RECOMMENDED
Eye Protection:SAFETY GLASSES
Other Protective Equipment:SKIN & EYES PROTECTION.
Work Hygienic Practices:AVOID CONTACT WITH EYES & SKIN.DO NOT GET ON
    CLOTHING.
Supplemental Safety and Health

==================  Physical/Chemical Properties  ==================

HCC:N1
Vapor Density:3.4
Spec Gravity:1.03
pH:8.5
Solubility in Water:NEGLIGIBLE
Appearance and Odor:BLACK PASTE/AMMONICAL ODOR(PASTE)
Percent Volatiles by Volume:3.0

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
NOT RECOMMENDED FOR USE ACRYLIC OR POLYCARBONATE SUBSTANCES
Stability Condition to Avoid:EXTREME HEAT
Hazardous Decomposition Products:NONE SPECIFIED BY MANUFACTURER.

====================  Disposal Considerations  ====================

Waste Disposal Methods:MATERIAL THAT CANNOT BE USED OR CHEMICALLY
    REPROCESSED SHOULD BE DISPOSED OF AT AN APPROVED FACILITY IN
    ACCORDANCE WITH AN APPLICABLE REGULATIONS UNDER RCRA. FOLLOW ALL
    STATE AND LOCAL REGULATIONS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.